6mm Energy Rubber Tiles

Subscribe to back in stock notification

Lowest cost gym tile.
Made in the USA.
Ships from both coasts to help maintain low shipping costs.
6 mm (approx 1/4") thick.
Easy to install and keep clean.

View All

More Information

Get your sweat on without breaking the bank! Our 6mm Energy Rubber Tiles are the perfect, low-cost solution for any home gym or light-duty commercial gym. Made from recycled rubber and available in one popular all-purpose color, these tiles are as eco-friendly as they are tough. Plus, with precision-cut locks, they'll fit together so seamlessly, you'll be impressed you didn't hire a pro installer. These babies are easy to install too, no adhesive needed! And when it comes to customization, these tiles are as versatile as they come. Grab your utility knife and straight edge, and voila - a custom wall-to-wall gym floor that will have your friends green with envy. Our Energy Tiles come backed by a 5-year warranty, so you can get fit with confidence!

Recommended Uses: Energy interlocking rubber tiles are an excellent rubber floor tile for use as flooring for home gyms and workout rooms, as commercial gym flooring in light-duty gyms, as dog kennel flooring, as basement and rec room flooring, and anywhere else a non-slip and shock absorbing resilient floor surface would be useful.

Details

Recycled ContentNo

Care and Maintenance Document

Installation of these interlocking tiles is very simple and usually done by the consumer. Typical installation of these tiles is as follows:

First, clean your subfloor, so it is free of all dirt, grease, or debris.
Start in one corner of the room with a corner tile and add border tiles outward along the adjacent walls.
Leave the other two edges of the room open and fill in the rest of the room, adding center, corner, and border tiles where you see fit.
After the open floor is covered, go back and cut in tiles along the opposite walls in the room. We recommend leaving a gap along the walls roughly the tiles' thickness being used to account for expansion and contraction of the floor in varied temperature ranges.

Note: When piecing interlocking tiles together, adhesives aren’t usually needed since the weight of the product is usually enough to keep the floor tiles from moving. However, if you do experience movement and would like to ensure that the tiles do not slide at all, you can use some double-sided tape or mat tape around the perimeter of the installation to prevent any movement.

Care and Maintenance Document

Energy tiles are extremely durable and easy to maintain. Maintenance of these interlocking tiles typically includes:

Vacuuming any loose crumbs, dust, or debris from the flooring surface when necessary.
Occasional damp mopping of the rubber tiles with a mild soap and water solution. A few recommended soaps are Dawn dish detergent or Tide laundry detergent.

Note: Do not use any solvent or oil style cleaners such as Pinesol, Lysol, Murphy’s Oil Soap, WD40, paint thinner, etc. since these types of cleaners will break down the flooring over time.

Care and Maintenance Document

5-Year Warranty.

Care and Maintenance Document

Reviews

Questions

Customer Questions And Answer

Our 6mm Energy Rubber Tiles do not have any data on sound attenuation, but they are tested for sound absorption and transmission. To get the testing results for these, please feel free to contact one of our customer service agents at 800-613-0996 and they will be more than happy to send it to you.

Our 6mm Energy Rubber Tiles only come in center tiles. To create border and corner tiles you will need to cut the tiles with a sharp utility knife and straight edge.

Our 6mm Energy Rubber Tiles will provide you with added comfort underfoot and shock absorbent over concrete.

Our 6mm Energy Rubber Tiles are water resistant, not waterproof. When water is spilled it will sit on top of the tile initially. Over time, the water may seep into the pores that are on the floor and eventually evaporate. What is typically left behind are the salts in minerals that were in the water.

Our 6mm Energy Rubber Tiles are very easy to clean and maintain. For large dirt and debris, you will want to sweep the tiles or use a vacuum without the brush attachment to remove it. For stuck-on dirt and debris, you can mop the tiles with a mild soap and water solution or our Rubber Floor Cleaner and Degreaser with a synthetic mop head. You will then want to let the flooring air dry.

You can install our 6mm Energy Rubber Tiles under a baseboard heater. The only thing you will notice with these tiles being near the heating source is some expansion and contraction. We would recommend leaving a 1/2" gap between the tile and wall to account for this added expansion and contraction.

Our 6mm Energy Rubber Tiles can handle the dropping of barbells on them. If the barbells are over 25lbs, we do recommend using a thicker rubber tile.

Our 6mm Energy Rubber Tiles would feel warm to the touch if placed in direct sunlight. To help mitigate this we would recommend wearing shoes when walking over the flooring or putting down rugs in the areas where the sun would hit the most.

Our 6mm Energy Rubber Tiles will not discolor most hardwood floors. It is very rare for this to happen. If you are concerned that our rubber tiles will stain your hardwood flooring, we recommend placing a plastic sheet under the tiles to prevent any discoloration.

You don't have to place anything under our 6mm Energy Rubber Tiles. The only thing you would have to do is make sure that the subfloor is free and clear of any dirt or debris.

Our 6mm Energy Rubber Tiles will not damage any carpet that they are installed over. We recommend installing our rubber tiles over low pile commercial carpet as this will provide a flat, solid surface to install the tiles on. You can install these over plush, residential carpet with a thick pad, but we don't recommend it as there is potential for a tripping hazard as the pad depresses. If you have a light colored carpet and are worried that the tiles will stain the carpet, we recommend placing...

You can install our 6mm Energy Rubber Tiles over a subfloor that is not perfectly flat. As long as the pits and peaks are not too extreme, over an inch, you won't have any issues. The one area that any pits or peaks can cause a real issue is at the point where the tiles interlock. These pits and peaks can prevent the tiles from interlocking properly.

Our 6mm Energy Rubber Tiles are not vulcanized. Our Energy Rubber Tiles do have a slight rubber odor to them. If you are sensitive to smells, we recommend mopping the flooring with a mild soap and water solution and letting the flooring air dry. You will want to make sure you have plenty of ventilation in the room you are installing the flooring. You may have to repeat this step a few times to get the smell to the desired comfort level.

Our 6mm Energy Rubber Tiles were designed to be used in home gyms where heavy equipment and weights would be dropped on them, so these rubber tiles will perform excellently in an office setting. Rolling chairs will not damage these tiles in any way. The only thing that could happen is if a tile were to come unlocked, and the chair was to move it a bit. To fix this, all you would have to do is just re-interlock the tile.

Our 6mm Energy Rubber Tiles can be installed over any hard, flat surface such as concrete, asphalt, plywood, tile, laminate, and the like. So our 6mm rubber tiles can be installed over existing tile with ease. They can also be installed over low pile commercial carpet with ease. The only thing that these tiles can't really be installed over is a high pile, thick padded residential carpet. This is due to a tripping hazard being created when the pad is depressed. To get around this issue, we ...

You can use our 6mm Energy Rubber Tiles in your garage without having to install them throughout. These tiles can be just installed in the area where you are wanting to work out. These tiles interlock very tightly and will stay in place.

Our 6mm Energy Rubber Tiles do not contain any flame retardants and have a fire rate of Class III.

You can park a car occasionally over our 6mm Energy Rubber Tiles. We don't recommend it as the tiles could pop out of place when turning or driving over the tiles. If you wanted to prevent that, you could use our polyurethane adhesives to keep the tiles in place. The only other thing you may notice is if your car were to leak oil onto the flooring, that over time the rubber will breakdown. If your car does leak oil, we recommend placing one of our Nitro Rolls over the tiles or one of AutoFloorGuards...

If you cut off all the tabs on our 6mm Energy Rubber Tiles, the size of the tile would be 23" x 23".

When interlocked, the size of our 6mm Energy Rubber Tiles is 23.25" x 23.25". So you will lose about 3/4 of an inch when you cut off the tabs. We do offer a tile calculator on the product page that will assist you in figuring out the number of tiles needed to cover your space. Our 6mm Energy Rubber Tiles will hold up just fine in freezing temperatures. Since they are made from the tread of commercial truck tires, they will not behave any differently than your tires in freezing temperatures.