Description – Recycled rubber paver tiles give you a long lasting, comfortable, and slip resistant replacement to the hard surfaces once found in the stables from years ago. Rubber paver tiles are the new choice in flooring for breeding stables across the country. These rubber tiles are easy to install and are virtually maintenance free while being offered in 3 beautiful equestrian colors. Rubber paver tiles provide your valuable investment with a safe, comfortable, slip resistant surface in both dry and wet conditions. These rubber paver tiles ship from our east coast location and are 100% made in the USA!
Material – Our rubber pavers are made from 100% high-quality recycled SBR tire rubber.
Size – Each paver tile is 24” x 24”
Thickness – 1 1/4"
Weight – 20 lbs
Recommended Uses – These rubber paver tiles have been used successfully in barn stalls, corridors, wash bays, saddling areas, breeding sheds, paddock areas, tunnels, horse paths, winners' circles, as well as parade areas and service roads. Rubber paver tiles are the number one flooring choice in breeding barns across the country!
Available For Order - Ships between Nov 25 - Dec 2
Cleaning & Maintenance Procedures - Cleaning is as simple as sweeping or blowing away the debris and hosing off the dirt. For a deeper clean just pressure wash the surface making sure you do not use more than 1200 psi.
Note: Do not use any solvent or oil style cleaners such as Pinesol, Lysol, Murphy’s Oil Soap, WD40, paint thinner, etc. as these types of cleaners will break down the rubber pavers surface over time.
Loose Lay Installation
A. Install the perimeter border system of your choice.
B. Dig out approximately 12 inches of soil below the desired level of the rubber paver tiles.
C. Replace the soil first with just over nine inches of compacted crushed stone and then add an additional inch of sand over the top of the stone.
D. Once your area has been properly prepared measure the width of the area to be covered at the center and snap a chalk line down the middle.
E. Determine the center of the chalk line you just marked and snap a second chalk line making a precise 90 degree right angle perpendicular to your first line.
F. Start laying the rubber paver tiles from left to right starting at the center point where your two chalk lines intersect.
G. Make sure your rubber paver tiles are lined up perfectly with your chalk lines when laying the first row and you will need to cut the last paver tile to fit tightly along your border.
H. Continue to fill in the rest of the paver tiles using that first row you started with as a guide until your entire area is completed.
Adhered Installation
Note: 1-3/4” or the 1-1/4" thick rubber paver tiles may be adhered or loose-laid.
A. Always let your rubber paver tiles and adhesive adjust to the temperature where they will be installed at for up to 48 hours prior to installation.
B. Clean the surface the rubber pavers will be adhered to making sure there is no loose debris or dust.
C. Once your area has been properly prepared measure the width of the area to be covered at the center and snap a chalk line down the middle.
D. Determine the center of the chalk line you just marked and snap a second chalk line making a precise 90 degree right angle perpendicular to your first line.
E. Starting at the center where your two lines intersect use a 1/8” square notched trowel to apply just enough polyurethane adhesive in an area that can be covered by rubber paver tiles within 30 minutes.
F. On top of the adhesive you just applied to the surface start laying the rubber paver tiles from left to right starting at the center point where your two chalk lines intersected.
G. Make sure your rubber paver tiles are lined up perfectly with your chalk lines when laying the first row and you will need to cut the last paver tile to fit tightly along your border.
H. Continue to fill in the rest of the paver tiles using that first row you started with as a guide until your entire area is completed.
Note: Do not let the adhesive cure on your hands or the surface of the rubber paver tiles because it is very difficult to remove. Wipe off any unwanted adhesive with a cloth and some mineral spirits as soon as possible.
9,707+ Verified Reviews
Over 200 Million Sqft
30 Day Money Back
Price Match
Free Samples
