Description - Emser Tile Impact Charisma Glass Mosaic captures the modern mosaic with picket, linear, and herringbone motifs. A wide array of gray and blue tones alternate in varying degrees for lively visual appeal in a gloss finish. The contemporary glass mosaic series is ideal for kitchen backsplashes, shower accent strips, and more.
||12" x 12", 10" x 12", 10" x 13"
|Scratch Hardness (MOHS)
|Shape of Tile
|Made in USA
Product Codes – W80CHARPO1212MOL, W80CHARFI1212MOL, W80CHARDE1212MOL, W80CHARWI1013MHB, W80CHARCH1013MHB, W80CHARCH1013MHB, W80CHARFL1013MHB, W80CHARGR1013MHB, W80CHARFI1013MHB, W80CHARDE1013MHB, W80CHARWI1212MOL, W80CHARDE1012MPK, W80CHARFI1012MPK, W80CHARWI1012MPK, W80CHARFL1212MLB, W80CHARCH1212MLB, W80CHARGL1212MLB, W80CHARGR1212MOL, W80CHARPO1012MPK, W80CHARGR1012MPK
Available For Order - Ships between Oct 29 - Nov 2
Porcelain & Ceramic tiles are easy to keep clean and maintain. Maintenance of the floor typically includes:
- Daily or weekly vacuuming or mopping of dirt, grit, dust, etc.
- Place doormats at all entrances to prevent tracked in dirt, rocks, moisture, and other debris.
- Glazed tiles should be cleaned routinely with an all-purpose, low VOC household or commercial cleaner.
- The entire area should be cleaned and scrubbed with cleaner solution by using a cotton mop, cloth, sponge, or non-metallic brush.
- Routine cleaners should never contain hazardous or polluting products including, but not limited to acids or ammonia. Acids can damage the grout and the glazed surface of the tile, while ammonia can cause discoloration of grout.
- When complete, be sure to rinse the entire area with clean water to remove all cleaning solution residue.
For detailed cleaning instructions, please Click Here.
General instructions for installing floor tile:
- Tile must be installed over structurally sound substrates. Any damaged, loose or uneven areas must be repaired, patched and leveled.
- Start by marking the center point of the room. Place a row of loose tiles along the center lines in both directions, leaving enough space for uniform joints (use tile spacers).
- Using the notched side of the recommended trowel, comb adhesive into standing ridges by holding the trowel at a 45-degree angle. Remove excess adhesive, leaving a uniform, ridged setting bed. Never spread a larger area that can be set in 15 minutes.
- Measure tiles to be cut carefully and mark with a pencil or felt-tip pen. Make straight or diagonal cuts with a tile cutter and curved cuts with a nipper. Be sure to mix tiles from several cartons as you set, for a blended effect.
- Begin installation in the center of the room. Finish each grid before moving to the next. Start with the first tile in the corner of the grid and work outward. Set tiles one at a time using a slight twisting motion. Insert tile spacers as each tile is set. Fit perimeter tiles in each grid last, leaving 1/4" gap between tile and wall.
- When grid is completely installed, tap in all tiles with a rubber mallet or hammer and wood block, to ensure a good bond and level plane. Remove excess adhesive from joints with a putty knife, and from tile with a damp sponge.
- Do not walk on tiles until they are set (usually in 24 hours).
Tips for installing large format floor tile:
- Large size floor tile installation requires particular attention to proper subfloor preparation, grout joint sizing, trowel selection, and mortar coverage.
- It is absolutely critical that large tile be installed on a level substrate.
- Installation Requirement: For proper bonding, medium bed mortar should be used in installing tiles with a dimensional length greater than 15 inches on any one side of the tile. Back buttering tiles of this nature in the installation process will also assure proper coverage for body.
For detailed installation instructions, please Click Here.