Complete Your Order
Contact Us
 
8am - 8pm EST Monday - Friday
10am - 7pm EST Saturday

Daltile Florentine

Visual representation of average product rating from all associated reviews using stars
1 reviews
Every Day Low Price! Not eligible for promotions
This product has been discontinued.
Please see comparable products below.
  • Marble look tile with reveal imaging.
  • Durable and low maintenance.
  • Low cost alternative to stone flooring.
  • Adds timeless elegance to any space.
  • High color variation from tile to tile.
  • Pre consumer recycled materials.
  • Rectifed edging.
Description - Featuring reveal imaging, the Florentine collection provides the look of an expensive marble flooring without the actual expense of natural stone flooring. In 4 beautiful colors, these high variation tiles are unique and provide a random look across the whole floor. With less headache during installation, care, and maintenance, these low cost marble tiles are a a great alternative.
Material – Glazed Porcelain with rectified edging.
Size – Available in 12" x 12", 12" x 24", and 24" x 24" tiles.
Thickness – 3/8" (9mm)
Shade Variation – High (V3)
Minimum Grout Joint Recommendation – 12 x 24 Wall, Floor and Mosaic: 1/8" (3/16" when rectangular sizes are used in a staggered brick-joint pattern. Overlap should not exceed 33%)
Application – Floors, walls, countertops, and exterior patios.
Breaking Strength – >325 lbs.
Case Weight – Each 12x12 case weighs ~46 lbs, each 12x24 case weighs ~66 lbs, and each 24x24 case weighs ~66 lbs.
Recommended Uses – The Florentine collection has been successfully installed to add a touch of timeless elegance in hallways, living rooms, kitchens, dining rooms, formal areas, bedrooms, bathrooms, and more.

Out of Stock - Pre-Order Now

Porcelain tiles are easy to keep clean and maintain. Maintenance of the floor typically includes:
  • Daily or weekly vacuuming or mopping of dirt, grit, dust etc.
  • Place door mats at all entrances to prevent tracked in dirt, rocks, moisture, and other debris.
  • Glazed tiles should be cleaned routinely with an all-purpose, low VOC household or commercial cleaner.
  • The entire area should be cleaned and scrubbed with cleaner solution by using a cotton mop, cloth, sponge, or non-metallic brush.
  • Routine cleaners should never contain hazardous or polluting products including, but not limited to acids or ammonia. Acids can damage the grout and the glazed surface of the tile, while ammonia can cause discoloration of grout.
  • When complete, be sure to rinse the entire area with clean water to remove all cleaning solution residue.
  • For detailed cleaning instructions, please Click Here.
General instructions for installing floor tile:
  • Tile must be installed over structurally sound substrates. Any damaged, loose or uneven areas must be repaired, patched and leveled.
  • Start by marking the center point of the room. Place a row of loose tiles along the center lines in both directions, leaving enough space for uniform joints (use tile spacers).
  • Using the notched side of the recommended trowel, comb adhesive into standing ridges by holding trowel at a 45-degree angle. Remove excess adhesive, leaving a uniform, ridged setting bed. Never spread a larger area than can be set in 15 minutes.
  • Measure tiles to be cut carefully and mark with a pencil or felt-tip pen. Make straight or diagonal cuts with a tile cutter and curved cuts with a nipper. Be sure to mix tiles from several cartons as you set, for a blended effect.
  • Begin installation in the center of the room. Finish each grid before moving to the next. Start with the first tile in the corner of the grid and work outward. Set tiles one at a time using a slight twisting motion. Insert tile spacers as each tile is set. Fit perimeter tiles in each grid last, leaving 1/4" gap between tile and wall.
  • When grid is completely installed, tap in all tiles with a rubber mallet or hammer and wood block, to ensure a good bond and level plane. Remove excess adhesive from joints with a putty knife, and from tile with a damp sponge.
  • Do not walk on tiles until they are set (usually in 24 hours).

Tips for installing large format floor tile:

  • Large size floor tile installation requires particular attention to proper subfloor preparation, grout joint sizing, trowel selection, and mortar coverage.
  • It is absolutely critical that large tile be installed on a level substrate.
  • Installation Requirement: For proper bonding, medium bed mortar should be used in installing tiles with a dimensional length greater than 15 inches on any one side of the tile. Back buttering tiles of this nature in the installation process will also assure proper coverage for body.
For detailed installation instructions, please Click Here.
For printable warranty information, please Click Here.
Don't see what you're looking for? 
No results found.
prev page 1 ... ... next page
prev page PREV
prev page PREV
NEXT next page
NEXT next page
Average Rating
Visual representation of average product rating from all associated reviews using stars
5.0/5.0

Visual representation of product rating from review using stars
  Stunning marble look!
Installed in Master bathroom
Anonymous from Mesa, AZ wrote...
I recently remodeled my house and I was obsessed with the idea of a marble bathroom. Like, straight out of Caesar's Palace marble bathroom. Of course, marble is soft and expensive so I started looking for tile lookalikes. I continued the Mohawk Treyburne Tile on the bathroom floor (it's the flooring in almost my entire house and I love it so much!), and I used this tile for the walls and facing areas. I cannot get over how stunning this tile looks! I swear everyone that comes over oohs and ahhs over our bathroom and talks about how it looks like a fancy hotel! I love the bright color - it makes the space look so bright and big. I couldn't be happier with my decision and I only wish I had also done our guest bathroom with the same tiles.
All Review Images icon View all customer images
Your item was added to the cart
Color:
Qty:
$0.00 total